set up error

Set up the zero bias error compensation model of gyroscope at different temperature change condition respectively.

建立了硅微陀螺在不同温度变化条件下的零偏误差补偿模型。

Put in order, compare, analyses it on the basis of data gathered, adopt based on the BP neural network model carry on method that data fit is it study temperature impact on error relation to come, thus set up error model then compensate.

在对所采集的数据进行整理、比较、分析基础上，决定采用基于BP神经网络模型的数据拟合方法来研究温度对误差的影响关系，从而建立误差模型并实施补偿。

Based on the least square principle, an extended SCGM ( 1,1)_ ( a0) model is set up considering the absolute error in an ideal state. Its computation method is also presented.

基于最小二乘原理，考虑理想状态下的绝对误差建立了一种拓广的SCGM（1,1）a0模型，并给出了计算方法。

I set up the mechanism position error contains the dimension error, mechanism of rotating joint clearance error and error calculation model. I get the motion reliability of mechanism.

本文建立了包含机构尺寸误差、转动副间隙误差和驱动误差的机构位置误差计算模型，解得机构的运动可靠度。

B: You can set up the fax machine to print a completion receipt. It will also print an error page if the fax does not go through.

B：你可以设定传真机打印一张完成回执，如果传真发送失败的话，传真机也会打印一张发送失败回执。

In context, using the system modeling methed in threshold cointegration system to set up threshold vector error correction model, to reevaluate our country nominal interest rate and inflation rate relationship. 3.

为此，在本文中利用门限协整建模方式中的系统建模法建立门限向量误差校正模型，重新评价我国名义利率和通货膨胀率之间的长期关系。

To decrease the effect slope of aiming line error of radome on the guidance control system of missile, the design of guidance controller was served as the parameter optimization, and optimization model was set up.

为减小天线罩瞄准线误差斜率对导弹制导控制系统的影响，将导引控制器的设计作为参数优化问题，建立了优化模型。

After you have ensured that an XML document is formatted correctly and you have set up your error handling, you still have to put the XML into some kind of usable object for JavaScript.

在您确保了XML文档的格式正确无误并且设置了错误处理之后，仍必须把XML置入某种JavaScript可用的对象中。

A measuring system of sensor, single chip microcomputer, data acquisition and display is set up to compensate orientation error in numerical control machine tool rotary table.

为了补偿数控机床回转工作台的定位夹紧误差，设计了定位误差检测系统；提出了利用传感器、单片机和数据采集部分等组成检测系统；

Set up a good error reporting solution.

建立一个有效的错误报告机制。

Subject function of systemic factors about landslide hazard zonation was set up by using Fuzzy math theory, and did best to avoid unwanted error by any wrong thing in the course of numbering factors, thereby cause standardization to number factors. 3.

利用模糊数学理论建立了滑坡危险度区划系统因素集的隶属度函数，使要素集的量化避免因各种失误而造成的不必要的误差，从而使各种因素的量化规范化。

The position relationship between beam axis and shaft axis was discussed in lapping with bending disk. The equation denoting the best distance of beam axis and shaft axis was set up, and the error was analyzed.

本文讨论了磨具弯曲成形法中梁轴线与转轴中心线位置之间的关系，给出确定梁轴线与转轴之间最佳距离的计算公式及误差分析。

As the coefficient is established, the curve of matching function can be set up. Non-linearity error and temperature error of magnetic sensors are compensated. Feasibility of the method is validated by experiment.

计算拟和函数的系数，系数确定后可以建立拟合曲线函数，对磁敏传感器的非线性、温度误差补偿，通过实验证明了方法可行。

The on-the-spot measuring links have influence on the truthfulness of the measured K1 value, for this reason, a judgement basis is set up for the error analysis of the measured K1 value and the gas leakage of apparatus.

现场测定环节影响K1测定值的真实性；建立了K1值测定的误差分析和仪器漏气判别依据；